How to Fit a Roof Rack to a Car Without Roof Rails

Roof Rack Guide

Fitting a roof rack for car without rails is still possible, but only one of two methods will work on your car — and which one depends on something you cannot see from outside.

Two methodsDoor frame hooks or factory fixed points
No drillingBoth methods fit without cutting the roof
Check firstThree places a hidden fixing point can be
Short answer: A car without roof rails can take a roof rack if you use either door frame hooks or the factory mounting points hidden under the door frame trim. Check for threaded holes under the rubber seal, under the trim strips, or behind small plastic caps. If the car has none of them, hooks are the only option without drilling.

Why a car without rails is a different problem

A roof rack needs something on the car to hold onto. Most racks are sold for cars that have roof rails — the two bars running front to back along the roof — because the rack simply clamps onto them. If your car was built without rails, there is nothing to clamp to, so the rack has to grip the body itself.

That is the whole difficulty, and it is why a roof rack for car without rails is a separate product rather than a variant of a normal one. The feet are shaped differently, the load is carried by the door frame rather than by a rail, and the fitting kit changes depending on what your roof actually has.

If you searched for a roof rack for car without rails and are not sure whether your car qualifies, the three checks below are the whole answer.

Roof rack for car without rails: the two fitting methods

There are only two ways to fit a rack to a rail-less roof without drilling, and both are used by the product shown in this guide.

MethodWorks onHolds byDrilling
Door frame hookRoof with no rails, no fixed points, no gutterMetal hook clamped over the door frame edgeNo
Reserved hole fixingRoof with factory threaded mounting pointsBolted into the original holesNo

To find out which one you have, check three places on your own car. All three are on the door frame, roughly level with the top of the window.

  1. Lift the rubber weather seal along the top of the door opening and feel underneath for a threaded hole.
  2. Look under the plastic or chrome trim strip that runs along the roof edge — some cars hide the threads there.
  3. Look for a small plastic cap roughly the size of a coin. On many cars the mounting nut is welded to the roof and then covered by that cap.

If you find a threaded hole in any of those places, your car can use the reserved hole method. If you find nothing at all, the door frame hook method is the one to use — and if the door frame edge is too rounded for the hook to bite, no rail-less rack will fit without drilling.

Method 1: door frame hooks, step by step

This is the method for a plain roof — no rails, no fixed points, no rain gutter, no T-slot. The hook carries the load by gripping the door frame, and the rubber pads spread that load so the paint is not marked.

Roof rack for car without rails — door frame hook installation, 12 steps
Installation, steps 1 to 12.
Roof cross bars fitted with door frame hooks
The same feet once fitted — hooks clamped over the door frame.

Two of the twelve steps are where most fitting mistakes happen.

Step 6 — do not over-tighten. The mounting screws are turned three full circles only. Going further crushes the rubber pad and distorts the hook, and a distorted hook no longer sits flat against the frame.

Step 11 — test for movement before you close the cover. Grip the bar and push it sideways and front to back. Any movement means the hook is not seated; loosen, re-seat, and tighten again. Once the lockable cover is closed you cannot check it without the key.

Method 2: reserved hole fixing, step by step

This is the stronger of the two methods, because the bar is bolted into the car’s own mounting points rather than clamped to the frame. It only works if the car has those points — which is why the check above matters.

Roof rack for car without rails — factory fixed point installation, 8 steps
Installation, steps 1 to 8.
Roof cross bars bolted to factory fixed points
The same fixing once fitted — bolted into the original mounting points.

Step 3 is the one that decides whether the bar sits straight. The adjustment screw has to be pressed and the leg pulled out to the same extension on both ends. If one end is longer than the other, the bar sits skewed and the load is uneven.

Step 7 — confirm the red knob is fully locked. This knob is the final safety point. A knob that is tight but not locked can work loose over a long drive, so check it by hand before closing the cover.

Which cars this usually applies to

The cars below commonly left the factory without roof rails. Trim level matters — a higher trim of the same model may have rails, in which case a normal rail-mounted rack is the right choice and this guide does not apply.

CarLikely method
Ford FocusDoor frame hook
Honda CivicDoor frame hook
Audi A4Door frame hook
Volkswagen GolfDoor frame hook
BMW 3 SeriesDoor frame hook
Mercedes C-ClassDoor frame hook
Toyota CorollaDoor frame hook
Bar length is matched to the vehicle rather than being universal. Send the model, year and trim before ordering and the correct length and fixing kit can be confirmed.

Roof bars vs roof rack, and how to install roof cross bars

The two terms are used loosely, and it is worth knowing the difference before you buy. A roof rack usually means the complete assembly, including any rails. Roof bars, or cross bars, are the two horizontal bars you actually load. When you search for a roof rack for car without rails — or for roof racks for cars without rails — what you are really looking for is a pair of cross bars with rail-less feet.

For roof bars for cars without rails the fitting sequence is the same on both methods: open the lock cover, set the feet, tighten, test for movement, close the cover. That is how to install roof cross bars on any rail-less car, and the two step-by-step diagrams above are the whole procedure.

If you are comparing car roof rack without rails options, check the fitting method in the description rather than the product name. A rack sold as a roof rack for car without rails still has to suit your specific roof — hook or reserved hole — and the two are not interchangeable. If your car does have rails, the process is different again, and the same advice applies: match the fitting method, not the label.

Questions buyers ask before ordering

Can I fit a roof box on a car without roof rails?

Yes, once cross bars are fitted. The roof box clamps to the bars, not to the car, so the bars are the part that has to suit your roof. Check the box weight against the bar load rating, not against the car’s own roof limit alone.

Is it safe at motorway speed?

A correctly seated hook or bolted fixing is safe at normal road speeds. What is not safe is a hook that was not tested for movement at step 11, or screws tightened past the recommended three turns. Both are checked by hand in under a minute.

Will it damage the paint?

The pads under each foot are there to prevent that. Fit them before the foot is tightened, and check that the pad is fully under the mounting foot rather than half out — step 7 of the reserved hole method shows the correct position.

My car has a rain gutter. Can I use this?

A gutter is a third type of mounting point and needs feet designed for it. Check the product description before ordering; do not assume a door frame hook will grip a gutter, because the shapes are different.

How long does fitting take?

About 20 to 30 minutes for a pair, including checking for movement and closing the covers. It is a one-person job with the supplied hex wrench.

What if my car has no fixing points and no usable door frame?

Then a rail-less rack cannot be fitted without drilling. Ask before ordering rather than after — send a photo of the door frame and the roof edge, and it can be confirmed from that.

What to check before you buy

Three things decide whether a rail-less rack fits: whether the roof has factory points, whether the door frame edge is flat enough for a hook, and whether the bar length matches the car. The first two you can check yourself in a few minutes using the method above. The third is quoted per vehicle, so it has to come from the seller.

We supply these cross bars with both fixing kits in the box, so the same set covers either case: universal roof rack cross bars. Send the model, year and trim, and we will confirm the length and which kit to use. The rest of the range is listed under roof rack.

Not sure which method your car needs?

Send us the model, year and a photo of the door frame. We will tell you which fixing kit fits before you order.